Product Code Database
In photography, a shutter is a device that allows light to pass for a determined period, exposing photographic film or a photosensitivity image sensor to light in order to capture a permanent image of a scene. A shutter can also be used to allow pulses of light to pass outwards, as seen in a movie projector or a signal lamp. A shutter of variable speed is used to control exposure time of the film. The shutter is constructed so that it automatically closes after a certain required time interval. The speed of the shutter is controlled either automatically by the camera based on the overall settings of the camera, manually through digital settings, or manually by a ring outside the camera on which various timings are marked.
Behind-the-lens shutters were used in some cameras with limited lens interchangeability. Shutters in front of the lens, sometimes simply a lens cap that is removed and replaced for the long exposures required, were used in the early days of photography. Other mechanisms than the dilating aperture and the sliding curtains have been used; anything which exposes the film to light for a specified time will suffice.
The time for which a shutter remains open (exposure time, often called "shutter speed") is determined by a timing mechanism. These were originally pneumatic (Compound shutter) or clockwork, but since the late twentieth century are mostly Electronics. Mechanical shutters typically had a Time setting, where the shutter opened when the button was pressed and remained open until it was pressed again, Bulb where the shutter remained open as long as the button was pressed (originally actuated by squeezing an actual rubber bulb), and Instantaneous exposure, with settings ranging from 30" to 1/4000" for the best leaf shutters, faster for focal-plane shutters, and more restricted for basic types. The reciprocal of exposure time in seconds is often used for engraving shutter settings. For example, a marking of "250" denotes 1/250". This does not cause confusion in practice.
The exposure time and the effective aperture of the lens must together be such as to allow the right amount of light to reach the film or sensor. Additionally, the exposure time must be suitable to handle any motion of the subject. Usually it must be fast enough to "freeze" rapid motion, unless a controlled degree of motion blur is desired, for example to give a sensation of movement.
Most shutters have a flash synchronization switch to trigger a flash, if connected. This was quite a complicated matter with mechanical shutters and flashbulbs which took an appreciable time to reach full brightness, focal-plane shutters making this even more difficult. Special flashbulbs were designed which had a prolonged burn, illuminating the scene for the whole time taken by a focal plane shutter slit to move across the film. These problems were essentially solved for non-focal-plane shutters with the advent of electronic flash units which fire virtually instantaneously and emit a very short flash.
When using a focal-plane shutter with a flash, if the shutter is set at its X-sync speed or slower the whole frame will be exposed when the flash fires (otherwise only a band of the film will be exposed). Some electronic flashes can produce a longer pulse compatible with a focal-plane shutter operated at much higher shutter speeds. The focal-plane shutter will still impart focal-plane shutter distortions to a rapidly moving subject.
Cinematography uses a rotary disc shutter in , a continuously spinning disc which conceals the image with a reflex mirror during the intermittent motion between frame exposure. The disc then spins to an open section that exposes the next frame of film while it is held by the registration pin.
Focal plane shutters have the advantage over central leaf shutters of allowing the use of interchangeable lenses without requiring a separate shutter for each lens. (Leaf shutters behind the lens also allow interchanging the lens using a single shutter.)
They have several disadvantages as well:
Simple leaf shutters have a single leaf, or two leaves, which pivot so as to allow light through to the lens when triggered. If two leaves are used they have curved edges to create a roughly circular aperture. They typically have only one shutter speed and are commonly found in basic cameras, including disposable cameras. Some have more than one speed.
A diaphragm or leaf shutter (as distinct from the simple leaf shutter above) consists of a number of thin blades which briefly uncover the camera aperture to make the exposure. The blades slide over each other in a way which creates a circular aperture which enlarges as quickly as possible to uncover the whole lens, stays open for the required time, then closes in the same way.Sidney Ray, Scientific Photography and Applied Imaging, Oxford: Focal Press, 1999 The larger the number of blades, the more accurately circular is the aperture. Flash synchronization is easily achieved with a pair of contacts that close when the shutter is fully open.
Ideally the shutter opens instantaneously, remains open as long as required, and closes instantaneously. This is essentially the case at slower speeds, but as speeds approach their maximum the shutter is far from fully open for a significant part of the exposure time. Effectively the shutter acts as an additional aperture, and may cause an increased depth of field, undesirable if shallow focus is being used creatively. Or it may cause mechanical vignetting if the diaphragm is outside of the lens (like a focal plane shutter or apodization filter).
The term diaphragm shutter has also been used to describe an optical stop with a slit, near the focal plane of a moving-film high-speed camera. Focal Encyclopedia of Photography, Macmillan, 1957
A few types and makers of leaf shutters became very well known. The early Compound shutter had a pneumatic mechanism, with a piston sliding against air resistance in a cylinder. They were quieter at slow speeds than clockwork, but potentially very inaccurate. More accurate clockwork mechanisms then replaced the airbrake, and the German Compur, and the later Synchro-Compur, became virtually the standard quality shutter. Later the Japanese Copal shutter was widely adopted in quality equipment. The German Prontor and Japanese Seikosha shutters were also widely used. Up and Down with Compur: The development and photo-historical meaning of leaf shutters, by Klaus-Eckard Riess, translated by Robert "The Professor" Stoddard gives a detailed history and technical description of leaf shutters. The company Compur Monitor was still in business , but made only gas detection systems. Leaf shutters under the Compur, Copal, and Seiko names are no longer manufactured.
Interchangeable-lens cameras with a central shutter within the lens body require that each lens has a shutter built into it. In practice most cameras with interchangeable lenses use a single focal plane shutter in the camera body for all lenses, while cameras with a fixed lens use a central shutter. Many medium-format and most large-format cameras, however, have interchangeable lenses each fitted with a central shutter. A few interchangeable-lens cameras have a behind-the-lens leaf shutter. Large-format often had a focal-plane shutter. Some had both a focal-plane shutter (for lens interchangeability) and a lens with central shutter (for flash synchronisation); one shutter would be locked open.
Film cameras, but not digital cameras, with a central shutter and interchangeable lenses often have a secondary shutter or darkslide to cover the film and allow changing lens in mid-roll without fogging the film.
The main advantages of central and behind-the-lens leaf shutters compared to a focal-plane shutter are:
Some disadvantages of the central shutter are:
Image sensors without a shaded full-frame double must use serialized data transfer of illuminated pixels called rolling shutter. A rolling shutter scans the image in a line-by-line fashion, so that different lines are exposed at different instants, as in a mechanical focal-plane shutter, so that motion of either camera or subject will cause geometric distortions, such as skew or wobble. Shutter Operations for CCD and CMOS Image Sensors Kodak (PDF)
Today, most digital cameras use combination of mechanical shutter and electronic shutter or mechanical shutter solely. Mechanical shutter can accommodate up to 1/16000 seconds (for example the Minolta Dynax/Maxxum/α-9 film camera had a maximum of 1/12000, a record in its era, and the later digital Nikon D1 series were capable of 1/16000), while electronic shutter can accommodate at least 1/32000 seconds, used for many superzoom cameras and currently many Fujifilm APS-C cameras (X-Pro2, X-T1, X100T and others).
Stacked CMOS sensors combine the image sensor itself with ADCs and digital memory in the same package. The readout of these sensors is faster than traditional sensors, because the digitized image is transferred into the digital memory in the sensor itself during readout and only afterwards transferred out of the sensor. This results in an electronic shutter which is as fast as a mechanical focal-plane shutter. Some cameras using stacked sensors, like the Nikon Z 9, completely removed the mechanical shutter. Dynamic range and noise performance are not compromised, because these sensors do not utilize a global shutter.
In many cases, autofocus (AF) lag is the root cause of shutter lag. Lower-cost cameras and low-light or low-contrast situations will make the effect more pronounced and it is in these cases that AF lag is more noticed. Most AF systems use autofocus to determine focus; in situations where contrast is low, the speed at which the camera can determine the best focus can be quite noticeable. Since most modern cameras will not activate the shutter until autofocus is complete, the result is shutter lag. In these cases, the photographer can switch to manual focus to avoid the delay that is attributable to the AF function.
Shutters are also used simply to regulate pulses of light, with no film being used, as in a signal lamp.
Central shutter
A central shutter is not a type of shutter as such, but describes the position of the shutter: it is typically a leaf shutter (or simple leaf shutter), and located within the lens assembly where a relatively small opening allows light to cover the entire image. Leaf shutters can also be located behind, but near, the lens, allowing lens interchangeability. The alternative to a central or behind-the-lens shutter is a focal-plane shutter.
Electronic shutter
Digital (both CMOS sensor and CCD image sensors) can be constructed to give a shutter equivalent function by transferring many pixel cell Electric charge at one time to a paired shaded double called frame transfer shutter. If the full-frame is transferred at one time, it is a global shutter. Often the shaded cells can independently be read, while the others are again collecting light. Electronic shuttering: Rolling vs Global shutter Motionvideoproducts Extremely fast shutter operation is possible as there are no moving parts or any serialized data transfers. Global shutter can also be used for videos as a replacement for rotary disc shutters.
Shutter lag
Shutter lag is the time between the shutter release being pressed and the exposure starting. While this delay was insignificant on most film and some digital cameras, many digital cameras have significant delay, which can be a problem with fast-moving subjects as in sports and other action photography. Release lag of a bridge camera such as the 2010 Pentax X90 is a relatively short 1/50 s, or 21 milliseconds (ms). The Canon EOS 50D DSLR is specified at 131 ms lag.
Shutter cycle
A shutter cycle is the process of the shutter opening, closing, and resetting to where it is ready to open again. The life-expectancy of a mechanical shutter is often expressed as a number of shutter cycles. Most digital cameras save the shutter cycle information along with the photos, which contains valuable information such as shutter speed, aperture, and shutter count. What is a Low Shutter Count: Understanding Camera Lifespan There are multiple websites and applications to access the EXIF data.
Projector shutter
In movie projector, the shutter admits light from the lamphouse to illuminate the film across to the projection screen. To avoid brightness flicker, a double-bladed rotary disc shutter admits light two times per frame of film in 24 fps projection, resulting in 24 * 2 = 48 Hz, which is the lower brightness flicker fusion threshold. For 16fps (most silent films and Regular 8mm) and 18fps (Super 8), a triple-bladed shutter is used instead, as 16 * 3 = 48 Hz and 18 * 3 = 54 Hz.
See also
External links
|
|
